The Intel (or i) programmable peripheral interface (PPI) chip was developed and manufactured by Intel in the .. “Intel 82c55 PPI Datasheet” (PDF) . Title, System Components. Description, Programmable Peripheal Interface. Company, Intel Corporation. Datasheet, Download A datasheet. Quote. A datasheet, A circuit, A data sheet: AMD – Programmable Peripheral Interface iAPX86 Family,alldatasheet, datasheet, Datasheet search site for.

Author: Douzragore Akisho
Country: Egypt
Language: English (Spanish)
Genre: Life
Published (Last): 3 July 2005
Pages: 388
PDF File Size: 9.92 Mb
ePub File Size: 13.2 Mb
ISBN: 609-7-34298-167-3
Downloads: 65013
Price: Free* [*Free Regsitration Required]
Uploader: Yozshujinn

Acknowledgement and handshaking signals are provided to maintain proper data flow and synchronisation between the data transmitter and receiver. The Intel or i Programmable Peripheral Interface PPI chip was developed and manufactured by Intel in the first half of the s for the Intel microprocessor.

The functionality of the is now mostly embedded in larger VLSI processing chips as a sub-function. So, without latching, the outputs would become invalid as soon as the write cycle finishes.

Since the two halves of port C are independent, they may be 8255 such that one-half is initialized as an input port while the other half is initialized as an output port.

It was later cloned by other manufacturers. As an example, consider an input device connected to at port A. Interrupt logic is supported. Microprocessor And Its Applications. Some of the pins of port C function as handshake lines.

Intel 8255

This mode is datasheft when D 7 bit of the Control Word Register is 1. Retrieved from ” https: For example, if port B and upper port C have to be initialized as input ports and lower port C and port A as output ports all in mode In this mode, the may be used to extend the system bus to a slave microprocessor or to transfer data bytes to and from 825a5 floppy disk controller.

This is required because the data only stays on the bus for one cycle. Input and Output data are latched. Intel Intel D For example, if port B and upper port C have to be initialized as input ports and lower port C and port A as output ports all in mode Each line of port C PC 7 – PC 0 can be set or reset by writing a suitable value to the control word eatasheet. Only port A can be initialized in this mode.

  BLOOD MAIDENS BARBARA HAMBLY PDF

In this mode, the may be used to extend the system bus to a slave microprocessor or to datasheet data bytes to and from a floppy disk controller.

For port B in this mode irrespective of whether is acting as an input port or output portPC0, PC1 and PC2 pins function as handshake lines.

Views Read Edit View history.

A/82C55A Device Description(#) A/82C55A Device Description

By using this site, you agree to the Terms of Use and Privacy Policy. Address lines A 1 and A 0 allow to access a data register for each port or a control register, as listed below:.

This page was last edited on 23 Septemberat Interrupt logic is supported. Retrieved 26 July This means that data can be input or output on the same eight lines PA0 – PA7. The two halves of port C can be either used together as an additional 8-bit port, or they can be used as individual 4-bit ports.

The is also directly compatible with the Zas well as many Intel datasheer.

This means that data can be input or output on the same eight lines PA0 – PA7. If from the previous operation, port A is initialized as an output port and if is not reset before using the current configuration, then there is a possibility of damage of either the input device connected or or both, since both and the device connected will be sending out data.

All of these chips were originally available in a pin DIL package. If an input changes while the port is being read then the result may be indeterminate. The two halves of port C can be either used together as an additional 8-bit port, or they can be used as individual 4-bit ports.

Address lines A 1 and A 0 allow to access a data register for each port or datasgeet control register, as listed below:.

The inputs are not latched because the CPU only has to read their current values, then store the data in a CPU register or memory if it needs to be referenced at a later time. From Wikipedia, the free encyclopedia. When we wish to use port A or port B for daatasheet strobed input or output operation, we initialise that port in mode 1 port A and port B can be initilalised to operate in different modes, i.

  JOHN MUNBY COMMUNICATIVE SYLLABUS DESIGN PDF

Acknowledgement and handshaking signals are provided to maintain proper data flow and synchronisation between the data transmitter and receiver. Port A can be used for bidirectional handshake data transfer.

Microprocessor And Its Applications. If from the previous operation, port A is initialized as dattasheet output port and if is not reset before using the current configuration, then there is a possibility of damage of either the input device connected or or both, since both and the device connected will be sending datashet data. The two modes are selected on the basis of the value present at the D 7 bit of the control word register. It is an active-low signal, i.

Retrieved 3 June Retrieved 3 June The i was also used with the Intel and Intel [1] and their descendants and found wide applicability in digital processing systems. The control signal chip select CS pin 6 vatasheet used to enable the chip.

The two modes are selected on the basis of the value present at the Dattasheet 7 bit of the control word register.

This mode is selected when D 7 bit of the Control Word Register is 1. The is a member of the MCS Family of chips, designed by Intel for use with their and microprocessors and their descendants [1].

Programmable Peripheral Interface – Intel Chipset Datasheet

Only port A can be initialized in this mode. For port B in this mode irrespective of whether is dztasheet as an input port or output portPC0, PC1 and PC2 pins function as handshake lines.

Since the two halves of port C are independent, they may be used such that one-half is initialized as an input port while the other half is initialized as an output port.