HP Color LaserJet CP Series Printer The only warranties for HP products and .. Manually configure IPv4 TCP/IP parameters from the control panel. View and Download HP CPdn – Color LaserJet Laser Printer service manual online. Color LaserJet CP Series Printer. CPdn – Color LaserJet. HP Color LaserJet cyan print cartridge CEA CE . NOTE: In this manual, the abbreviation “PCA” stands for “printed circuit-board assembly.”.
|Published (Last):||19 January 2010|
|PDF File Size:||8.42 Mb|
|ePub File Size:||20.69 Mb|
|Price:||Free* [*Free Regsitration Required]|
The registration shutter aligns the paper correctly to prevent skewed printing. Use this option to append the required carriage return to each line feed. Secondary transfer The paper acquires a positive charge from the secondary-transfer roller, and so it attracts the negatively charged toner from the surface of the ITB. Pcl Sub-menu Menu item Values Description printable area is eighty pitch characters on a single line.
HP Color LaserJet CP Series Printer – Control panel | HP® Customer Support
Page 92 Remove the HP postcard media insert Adjust the paper-length and paper-width guides by squeezing the adjustment latches and adjusting the guides to the fully opened position. Allows you to configure the daily wake time for the product to avoid warm-up or calibration time.
If the engine-test page does not print, try removing the formatter and then performing the engine test again. The duplexing unit consists of the following components: Check the paper to verify the guides lightly touch the stack, but do not bend it.
The remainder of this chapter provides steps for correcting problems. Figure Remove the RD sensor assembly 5 of 6 Remove the assembly. The product is heavy. Disconnect one connector callout 7remove two screws callout 8and then carefully lift the assembly callout 9 off of the product to remove it. The spring is not captive.
Answer questions, earn points and help cp5325dn Answer questions. A thorough cleaning of all paper path parts with alcohol prep pads, or Glass Plus and quality paper towels, will reduce this gum build up.
Do not use a pozidrive screwdriver callout 2 or any motorized screwdriver. Menu item Values Description printable area is eighty pitch characters on a single line. How to use the parts lists and diagrams The figures in this chapter show the up subassemblies in the product and their component parts.
Select YES to append a carriage return to each line-feed that is encountered in backward-compatible PCL jobs pure text, no job control. Low-voltage power supply Before proceeding, remove the following components: Range is —10 through Allows you to change the printable area of A4 paper.
Disconnect the two smaller connectors on the right side from the top. Drum motor 2 or drum motor 3 Before proceeding, remove the following components: Insert and tighten the retaining screws that came with the print server card.
Change Print Cartridges Change print cartridges When a print cartridge cp3255dn the end of its estimated useful life, the control panel displays a message recommending that you order a replacement.
Numerical parts list Table Numerical parts list Part number Description Table and page CC 1 x sheet feeder replacement kit 1 x paper feeder on page CC 1 hpp sheet feeder right door kit 1 x paper feeder on page CC ITB kit Control panel overlay SV CC Page Page – Jams in Tray 1, Tray 2 and internal pape Print a configuration page.
A critical error has occurred.
HP Color LaserJet CP3525 Series Printer – Control panel
HP Color LaserJet CP Printer User Guides | HP® Customer Support
Select YES to choose all tests. Rear-top cover Before proceeding, remove the following components: Grasp the roller shaft collars, and lift the transfer roller off of the product.
When the product is turned on and at the end of each print job, all four of the developing rollers disengage from the photosensitive drums. Please see the link below to contact the manufacturer and find out how to replace your printed manual.
Paper does not feed from Tray 2 or Menu Hierarchy Menu hierarchy The following top-level menus are available: A T half-duplex selection is not supported. Specify whether the current security settings on the print server will be saved or reset to factory defaults. Remove the antistatic foam callout Laser-beam exposure Page – Step 6: Verify that the transfer belt and transfer roller are correctly installed. Figure Remove the secondary transfer assembly 2 of 2 Reinstall the secondary transfer assembly Press and hold down the blue release lever when you reinstall the assembly.
The detected laser intensity does not match a specified value when the product initializes. Figure Remove the transfer roller 2 of 3 Push the pin on the release-lever side of the assembly toward the inside of the product to release it, and then lift the assembly up.
Select NO to have the product calibrate immediately when it wakes up or is turned on. Page Page – K right and front door interlock switche Remove the new toner collection unit from its packaging. Table Supported paper and print media sizes Size and dimensions Tray