LM/-Q1 does not rely on output capacitor ESR An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in. LM Synchronous 1MHz A Step-Down Voltage Regulator from the PowerWise® Family The LM Synchronously Rectified Buck Converter features all. The LM Synchronously Rectified Buck Converter Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

Author: Zolozragore Misida
Country: Trinidad & Tobago
Language: English (Spanish)
Genre: Travel
Published (Last): 24 February 2012
Pages: 178
PDF File Size: 2.37 Mb
ePub File Size: 2.78 Mb
ISBN: 136-6-88051-594-5
Downloads: 32206
Price: Free* [*Free Regsitration Required]
Uploader: Shaktishura

Nonetheless, such components are subject to these terms. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. It then drops to zero at turn-off. In some cases, TI components may be promoted specifically to facilitate safety-related applications.

The design of the demonstration board is detailed below.

LM3 Molded Inductor

Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. The exposed pad is internally connected to the LM IC substrate. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed.

Buyers are responsible for their products and applications using TI components. I wish to measure a very low resistance of the order of an ohm. This user’s guide details ml3102 design of a demonstration board which provides a 3. A load which creates significant transients requires a larger output capacitor than a fixed load. Calculate the feedback resistors The ratio of the feedback resistors can be calculated from the following equation: The output capacitor C10, C11 should be connected close to the load and tied directly to the ground plane.

  ECC85 DATASHEET PDF

If the output voltage is higher than 1. Vias should be added to dataseet the ground of the input capacitors to a ground plane, located as close to the capacitor as possible. Information published by TI regarding third-party dataxheet or services does not constitute a license to use such products or services or a warranty or endorsement thereof. In this demonstration board, a 10 nF capacitor is used. Products Applications Audio www. The average current during the on-time is the load current.

Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. Resale of TI components lm302 services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. A low ESR 0. Experimentation is usually necessary to determine the adtasheet value for the output capacitor, as the nature of the load may require a larger value.

Once ILR is selected, L can be determined by: Typical performance and operating waveforms are also provided for reference. TI is not responsible or liable for any such statements. TI is not catasheet or liable for such altered documentation. The input capacitor is calculated from: Documents Flashcards Grammar checker. The operating frequency remains constant with line variations due to the inverse relationship between the input voltage and the on-time.

Calculate the on-time setting resistor The switching frequency fSW of the demonstration board is affected by the on-time ton of the LM, which is determined by R1. Protection features include output over-voltage protection, thermal shutdown, VCC undervoltage lock-out, gate drive under-voltage lock-out. The connection from the PGND pin to the input capacitors should be datashwet short and direct as possible.

  HONEYWELL HR-20E PDF

For a worst case calculation, the input capacitor must be capable of supplying this average load current during lm31022 maximum on-time. Using numerous vias to connect the die attached pad to the ground plane is a good practice.

LM datasheet, Pinout ,application circuits LM3 Molded Inductor

Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions.

The bootstrap capacitor C4 should be connected as close to the SW and BST pins as possible, and the connecting traces should be thick. Judicious positioning of the PC board within the end product, along with the use of any available air flow forced or natural convection can help reduce the junction temperature.

The exposed pad on the bottom of the LM IC package can be soldered to the ground plane, which should extend out from beneath the LM to help dissipate heat. How much energy is. C8 should be no smaller than nF for stability, and should be a good quality, lm3012 ESR, ceramic capacitor.